Digital Key Telephone System LDK-300 Programming Manual (стр. 34 )

15.17 ACNR TONE CADENCE (PGM 423)

Ring back tone, busy tone, error tone, or secondary dial tone may be programmed for ACNR.

PROCEDURE

ACNR TONE CADENCE (20MS) DIAL (1-4)	(1)  [TRANS/PGM] + 423.
RBACK TONE CADENCE ON:050 OFF:MS)	(2)  To change ACNR tone cadence, dial 1-4 and press BTN 1 (T1) or BTN 2 (T2) and dial 4 digits to enter new cadence.
ACNR TONE CADENCE (20MS) DIAL (1-4)	(3)  Press the [HOLD/SAVE] button for updating database permanently.
ACNR TONE CADENCE (20MS) DIAL (1-4)	l  Press the [CONF] button instead of the [HOLD/SAVE] button, then system goes to step (1) without updating system memory.

BTN	ITEM	RANGE	DEFAULT	REMARK
1	Ring-Back Tone		ON: 050 / OFF: 100	20msec base
2	Busy Tone		ON: 025 / OFF: 025	20msec base
3	Error Tone		ON: 012 / OFF: 012	20msec base
4	S-Dial Tone		ON: 070 / OFF: 000	20msec base

TABLE 15.17.1 Button Configuration for ACNR Cadence (PGM 423)

16. INITIALIZATION (PGM 450)

The system has been pre-programmed with certain features which are called default data. These features are loaded into memory when the system is initialized. The system should be always initialized when installed or at any time the database has been corrupted. To initialize the system to the default values, proceed as follows;

PROCEDURE

INITIALIZATION PRESS FLEX KEY (1-15)	(1)  [TRANS/PGM] + 450.
INITIALIZATION FLEX NUM PLAN	(2)  Press one of Flex. BTNs (1-15) as described below table (Ex. Flex. BTN 1).
INITIALIZATION FLEX NUM PLAN	(3)  Press the [HOLD/SAVE] button, then database is initialized with default data. Confirmation tone is heard.

BTN	ITEM	REMARK
1	Flexible Numbering Plan Initialization	PGM105, PGM106, PGM107
2	Station Database Initialization	PGM110, PGM111, PGM112, PGM113, PGM114, PGM 116, PGM117, PGM118, PGM119, PGM121, PGM122, PGM123, PGM124, PGM179
3	CO Line Database Initialization	PGM140, PGM141, PGM142, PGM143, PGM144
4	System Feature Database Initialization	PGM160 – PGM 177
5	Station Group Database Initialization	PGM190, PGM191
6	ISDN Tables Database Initialization	PGM201, PGM202, PGM230, PGM231
7	Reserved	None(Reserved)
8	System Timer Database Initialization	PGM180 – PGM182
9	Toll Table Database Initialization	PGM224, PGM225
10	LCR Database Initialization	PGM220 – PGM222
11	Tables Initialization	PGM227 – PGM229, PGM232 – PGM235
12	Flexible Button Program Initialization	PGM115
13	QSIG Database Initialization	PGM 320, PGM321,PGM322,PGM323, PGM 324
14	All Database Initialization	Above All
15	System Reset By Software

TABLE 16.1 Initialization (PGM 450)

17. PRINT PROT DATABASE (PGM 451)

In order to obtain a hard copy printout of the database, a printer should be connected to the RS-232C connector.

PROCEDURE

PROT DATA PRINT PRESS FLEX KEY (01-14)	(1)  [TRANS/PGM] + 451.
PROT DATA PRINT STATION DATA	(2)  To print database, press one of Flex. BTNs 01-14 and if there are entered data for selecting printed part, then selected database name will be displayed on the LCD.
PROT DATA PRINT STATION DATA	(3)  To print out the selected database at step (2), press the [HOLD/SAVE] button. (Ex. Station Database). After printing database, confirmation tone is heard.

BTN	ITEM	RANGE	DEFAULT	REMARK
1	Flexible Numbering Plan Print
2	Station Database Print	STN_R
3	CO Line Database Print	CO_R
4	System Feature Database Print
5	Station Group Database Print
6	ISDN Tables Database Print
7	System Timer Database Print
8	Toll Table Database Print
9	LCR Database Print
10	Other Tables Print
11	Nation Specific Database Print
12	Flexible Button Program Print	STN_R
13	All Database Print
14	LCD Message Print
1	Language	00 – 12	Nation specific	00:ENG 01:ITA 02:FIN 03:DUT 04:SWE 05:DAN 06:NOR 07:HUN 08:GER 09:FRE 10:POR 11:SPA 12:KOR
2	Station Type	0 – 2	0	0: NORMAL 1:LG-GAP 2:LARGE

TABLE 17.1 Database Print (PGM 451)